Mixed Video Pack

• Make sure you have access to your modem and a power point. If you don’t have a WPS capable modem, skip step 2 and see the ‘Ethernet install‘ instructions below
• Login to the morepork.nz/portal on your computer or tablet. We recommend you use an up to date browser, ideally Firefox, Safari or Chrome.
• Make sure your computer/tablet is connected to the same WiFi network you want to connect your video camera to.

Watch Demo:

Install instructions:

1. Connect your video camera to power using the supplied power cable in an area close to your modem.
2. Make sure the flashing red LED shows on your video camera before you continue, this may take 10 – 20 seconds.
3. Enable WPS on your modem by holding down the button for 2-3 seconds.
4. Next, press and hold the WPS button on the back of your video camera until the LED light on the front is flashing blue – it may flash read or blue first, don’t worry, this is normal. The video camera will remain flashing blue while it connects to your modem, this can take a minute or two.
5. The LED on your video camera will begin flashing green and then go solid green once it’s connected to your modem. When you see the solid green LED, your video camera has successfully paired to your modem.
6. While you are waiting for this, make sure your control panel is connected to WiFi, if you haven’t already done so.
7. Log into the web portal by visiting morepork.nz/portal to set up your video camera.
8. Click ‘Video‘. If this is your first video device, click ‘Add camera to this account‘ then install. If it’s not your first video device, click ‘Settings‘ then ‘Add Video Device‘
   Note – your camera may require a firmware upgrade. It will automatically do this as part of installation, just follow the on screen prompts.
9. Make sure your computer is on the same WIFI network as your camera then it should display on screen.
10. If you see ‘No new cameras were found’, enter the 12-digit MAC address that can be found on the bottom of your video camera and your camera will appear.
11. Once the video camera has been successfully added check out the video by clicking ‘Live Video‘. It may take a couple of minutes to load, and then you’ll see live footage. Adjust the position of the camera until you’re happy with the view it captures.
12. To add another video camera, go to the ‘Video’ tab and choose ‘Settings’.

1. Make sure you have access to your WPS capable modem and a power point
2. If you are getting your outdoor video camera hardwired to mains power, we recommend you get it set up with your Morepork using the supplied power adaptor first, to ensure everything runs smoothly.
3. Visit morepork.nz/portal on your computer or tablet and login using the details you set up at purchase.
4. We recommend you use an up to date browser, ideally Firefox, Safari or Chrome.

Watch demo:

Connect:

1. Connect your outdoor video camera to the power adaptor, and plug it into the wall near you WiFi modem.
   Note – If you want to hardwire your outdoor camera into mains power, you can do this later – best to get it set up with the power adaptor first.
2. Turn the wall switch on, and wait for the LED on the back of the camera to turn solid red or flashing white – This may take a minute or two.
3. Enable WPS on your modem – this differs depending on your modem. Typically, it may involve pressing or holding down the WPS button for a few seconds. If this doesn’t work, refer to your modem instructions for how WPS works. These can often be found online if you don’t have them.
4. Press and hold the WPS button on the back of the video camera for about 3 seconds, until the LED starts flashing blue, then release the button. Your video camera will now start pairing to your modem. The LED will cycle through solid red and flashing green while it’s setting up. This can take up to 5 minutes, so be patient. Once the LED is solid green, your camera has successfully connected to your modem
5. Login morepork.nz/portal and  click the ‘Video’ tab
6. Click ‘Settings’ then scroll down to click ‘Add Video Device’
   Note – if this is your first video camera, you can simple click ‘Add camera to this account’ from any screen on the video tab.
7. Your video camera should display with an ‘Install’ button. If not, click ‘Refresh’ or try entering the 12 digit MAC address from the back of your camera.
8. You can name your camera here too. Then click ‘Install’. The status bar will show you the progress. Wait a few minutes for your camera to pair to your Morepork.
9. When your camera has finished setting up, click ‘Live View’ to see a live stream.

Your video camera is now connected to your Morepork. If you wish to hardwire it, we recommend you get a professional to do this.

You can enable video motion detection (VMD) on your indoor or outdoor video cameras, to record clips around 40 seconds long when it detects motion.

To set up VMD:

1. Login to morepork.nz/portal using your username and password you set up and purchase
2. Click ‘Video’ then ‘Settings’
3. Click on ‘Video Motion Detection’
4. Customise your motion detection settings, we recommend:
   Sensitivity – this is how sensitive your motion detection is. We recommend setting it to 5 to start with.
   Target size – this is the percentage of the VMD window that needs to change before it will record. Depending on the size of your window, this might take a bit of trial and error – the smaller the window, the larger you should make the target size, to prevent too many false motion recordings.
   Window size – this is the area the motion detection will record light changes in. We recommend drawing windows only where there shouldn’t be movement. (i.e. for an outdoor camera, exclude adding a window on a tree, as there will be a lot of light changes).
5. Click ‘Save‘

Please note:

• Your video cameras will never trigger an alarm, even with motion detection enabled.
• Motion detection on your video cameras is a lot more sensitive than an image sensor and may respond to light changes. We recommend you test it out and update your settings to ensure you are recording only what you want and don’t run out of storage.

Important – you must also add  a recording schedule – without this, your motion detection won’t record anything.

1. Click ‘Recording Schedules’ at the top of the screen
2. Click ‘Add Schedule‘
3. Click ‘Video Motion Detection‘
4. Set up your recording schedule time frame, delay, at home settings and recipients.
   Adding a recipient will ensure someone will be notified if any motion is detected. We recommend you setup push notifications so you can be alerted to your phone. See here for details.
5. Click ‘Save Schedule’

Your video motion alerts are now all setup! Remember, you can change the sensitivity of your motion detection and update your recording schedules at any time.